Difference between revisions of "Scanning Beams"
(22 intermediate revisions by 5 users not shown) | |||
Line 1: | Line 1: | ||
+ | {{DISPLAYTITLE:2015 Scanning Beams}} | ||
− | + | == LFI beams == | |
− | ==File Names== | + | We released maps of the Stokes parameters of the band-averaged [[Beams LFI#Polarized_Scanning_Beams_and_Focal_Plane_calibration|scanning beams]]. The averages are performed using the [[The_RIMO#LFI_2|RIMO]] bandpass, assuming a flat spectrum of the incoming radiation. The Stokes parameters maps contain the complete information about the field intensity and polarization properties. Main Beam, Intermediate Beam, and Sidelobes are released separately. |
+ | |||
+ | More information on LFI beams can be found at {{PlanckPapers|planck2014-a05}} and on HFI beams at {{PlanckPapers|planck2014-a08}} | ||
+ | |||
+ | ===File Names=== | ||
The file names are of the form: | The file names are of the form: | ||
Line 10: | Line 15: | ||
where | where | ||
* ''fff'' denotes the frequency | * ''fff'' denotes the frequency | ||
− | * mb denotes the Main Beams | + | * ''mb'' denotes the Main Beams |
− | * ib denotes the Intermediate Beam | + | * ''ib'' denotes the Intermediate Beam |
− | * sl denotes the Sidelobes | + | * ''sl'' denotes the Sidelobes |
* ''rrr'' denotes the radiometer | * ''rrr'' denotes the radiometer | ||
− | * R2.nn is the version. | + | * ''R2.nn'' is the version. |
At the present time, HFI is not releasing the Scanning Beams. | At the present time, HFI is not releasing the Scanning Beams. | ||
− | + | ===FITS file structure=== | |
− | ==FITS file structure== | ||
The FITS files contain a primary extension with no data and a minimal header, and one BINTABLE extension with data and with a description of the data in the header keywords. | The FITS files contain a primary extension with no data and a minimal header, and one BINTABLE extension with data and with a description of the data in the header keywords. | ||
The BINTABLE extension consist in four columns, each containing the array of one Stokes parameter. | The BINTABLE extension consist in four columns, each containing the array of one Stokes parameter. | ||
Line 31: | Line 35: | ||
Main Beam, Intermediate Beams and Sidelobes are saved with a different data format: | Main Beam, Intermediate Beams and Sidelobes are saved with a different data format: | ||
− | * Main Beams are projected on the tangent plane to the sphere, and sampled on a grid. The grid include an angular region | + | * Main Beams are projected on the tangent plane to the sphere, and sampled on a grid. The grid include an angular region expressed by the keyword ''angularCut'', and its dimensions are given by the keywords ''Nx'' and ''Ny'', representing the number of columns and rows. Each column of the BINDATA extension contains the sequence of the <math>Nx \times Ny</math> samples of the map in row major order. The keywords ''Xcentre'' and ''Ycentre'' express the coordinates of the beam maximum (i.e. where the sphere intersect the tangent plane). |
{| border="1" cellpadding="3" cellspacing="0" align="center" style="text-align:left" width=800px | {| border="1" cellpadding="3" cellspacing="0" align="center" style="text-align:left" width=800px | ||
Line 37: | Line 41: | ||
|- bgcolor="ffdead" | |- bgcolor="ffdead" | ||
− | ! Column Name || Data Type || Units || Description || | + | ! Column Name || Data Type || Units || Description || Comment |
|- | |- | ||
|BEAMDATA || Real*4 || none || Stokes parameter I || | |BEAMDATA || Real*4 || none || Stokes parameter I || | ||
Line 67: | Line 71: | ||
− | * Intermediate Beams and Sidelobes are sampled on the sphere. The resolution in <math>\theta</math> and <math>\phi</math> is given by the keywords "Ntheta" and "Nphi". The columns contain the sequence of Nphi Stokes parameters for each <math>\theta</math>. | + | * Intermediate Beams and Sidelobes are sampled on the sphere. The resolution in <math>\theta</math> and <math>\phi</math> is given by the keywords "Ntheta" and "Nphi". The columns of the BINDATA extension contain the sequence of Nphi Stokes parameters for each <math>\theta</math>. |
{| border="1" cellpadding="3" cellspacing="0" align="center" style="text-align:left" width=800px | {| border="1" cellpadding="3" cellspacing="0" align="center" style="text-align:left" width=800px | ||
|+ '''Intermediate Beam and Sidelobes file structure''' | |+ '''Intermediate Beam and Sidelobes file structure''' | ||
− | |- bgcolor="ffdead" | + | |- bgcolor="ffdead" |
− | ! Column Name || Data Type || Units || Description || | + | ! Column Name || Data Type || Units || Description ||Comment |
|- | |- | ||
|BEAMDATA || Real*4 || none || Stokes parameter I || | |BEAMDATA || Real*4 || none || Stokes parameter I || | ||
Line 87: | Line 91: | ||
! Keyword || Data Type || Value || Description || Comment | ! Keyword || Data Type || Value || Description || Comment | ||
|- | |- | ||
− | |Ntheta || Int || || <math>theta</math> samples number || | + | |Ntheta || Int || || <math>\theta</math> samples number || colatitude |
|- | |- | ||
− | |Nphi || Int || || <math>phi</ | + | |Nphi || Int || || <math>\phi</math> samples number || longitude |
|- | |- | ||
− | |Mintheta || Float || | + | |Mintheta || Float || || Minimum value of <math>\theta</math> || |
|- | |- | ||
− | |Maxtheta || Float || || Maximum value of <math>theta</math> || | + | |Maxtheta || Float || || Maximum value of <math>\theta</math> || |
|- | |- | ||
− | |angularCut || Float || || Angular cut [deg] || | + | |angularCut || Float || || Angular cut [deg] || |
|} | |} | ||
+ | |||
+ | == HFI Beams == | ||
+ | |||
+ | The HFI scanning beams are a combination of observations of Saturn, for the central parts, and Jupiter, for the wings, as described in the [[Beams | Beams]] section of this document, and in Section 4.1 of {{PlanckPapers | planck2014-a08}} on ''Hybrid beams''. Saturn data are used where they are signal-dominated; when the SNR of Saturn drops to < 9, Jupiter data are used, after binning them azimuthally. Beyond that, i.e., below the noise floor of the Jupiter data, and out to 100 arcmin, a power law (~θ<sup> -3</sup>) is used, where the exponent is derived from GRASP physical optics models. The figure below, taken from the [[Beams#Key_Changes | Beams]] section of this document, shows graphically the different portions of the beam model. | ||
+ | |||
+ | |||
+ | [[Image:HybridBeamDiagram.png|thumb|500px|center| Scanning beam map for detector 143-6 showing a rough diagram of the regions that are handled with a different | ||
+ | data selection or binning.]] | ||
+ | |||
+ | |||
+ | The beams are provided in FITS files named | ||
+ | * ''HFI_ScanBeam_{det-name}_R2.nn.fits'', | ||
+ | where ''det-name'' is of the form ''100-1a'', and ''nn'' is the version number. Each file contains a single ''IMAGE'' extension. The image is 6001x6001 pixels of size 2x2 arcsec<sup>2</sup> (given in the ''DELTAX'' and ''DELTAY'' keywords), centred on pixel 3001,3001, and normalised to 1 at the maximum, where ''X'' and ''Y'' and in the Dxx reference system. | ||
+ | |||
+ | == References == | ||
+ | <References /> |
Latest revision as of 14:33, 15 April 2015
LFI beams[edit]
We released maps of the Stokes parameters of the band-averaged scanning beams. The averages are performed using the RIMO bandpass, assuming a flat spectrum of the incoming radiation. The Stokes parameters maps contain the complete information about the field intensity and polarization properties. Main Beam, Intermediate Beam, and Sidelobes are released separately.
More information on LFI beams can be found at Planck-2015-A04[1] and on HFI beams at Planck-2015-A07[2]
File Names[edit]
The file names are of the form:
LFI_ScanBeam-{mb,ib,sl}_{fff}-{rrr}_R2.{nn}.stokes
where
- fff denotes the frequency
- mb denotes the Main Beams
- ib denotes the Intermediate Beam
- sl denotes the Sidelobes
- rrr denotes the radiometer
- R2.nn is the version.
At the present time, HFI is not releasing the Scanning Beams.
FITS file structure[edit]
The FITS files contain a primary extension with no data and a minimal header, and one BINTABLE extension with data and with a description of the data in the header keywords. The BINTABLE extension consist in four columns, each containing the array of one Stokes parameter. The columns are called:
- Beamdata , containing
- BeamdataQ, containing
- BeamdataU, containing
- BeamdataV, containing .
Main Beam, Intermediate Beams and Sidelobes are saved with a different data format:
- Main Beams are projected on the tangent plane to the sphere, and sampled on a grid. The grid include an angular region expressed by the keyword angularCut, and its dimensions are given by the keywords Nx and Ny, representing the number of columns and rows. Each column of the BINDATA extension contains the sequence of the samples of the map in row major order. The keywords Xcentre and Ycentre express the coordinates of the beam maximum (i.e. where the sphere intersect the tangent plane).
Column Name | Data Type | Units | Description | Comment |
---|---|---|---|---|
BEAMDATA | Real*4 | none | Stokes parameter I | |
BEAMDATAQ | Real*4 | none | Stokes parameter Q | |
BEAMDATAU | Real*4 | none | Stokes parameter U | |
BEAMDATAV | Real*4 | none | Stokes parameter V | |
Keyword | Data Type | Value | Description | Comment |
Nx | Int | 601 | X axis samples number | X axis aligned with the direction of the S arm |
Ny | Int | 601 | Y axis samples number | Y axis aligned with the direction of the M arm |
Xcentre | Int | 301 | X coordinate of the beam centre | |
Ycentre | Int | 301 | Y coordinate of the beam centre | |
Xdelta | Float | X step in radians | ||
Ydelta | Float | Y step in radians |
- Intermediate Beams and Sidelobes are sampled on the sphere. The resolution in and is given by the keywords "Ntheta" and "Nphi". The columns of the BINDATA extension contain the sequence of Nphi Stokes parameters for each .
Column Name | Data Type | Units | Description | Comment |
---|---|---|---|---|
BEAMDATA | Real*4 | none | Stokes parameter I | |
BEAMDATAQ | Real*4 | none | Stokes parameter Q | |
BEAMDATAU | Real*4 | none | Stokes parameter U | |
BEAMDATAV | Real*4 | none | Stokes parameter V | |
Keyword | Data Type | Value | Description | Comment |
Ntheta | Int | samples number | colatitude | |
Nphi | Int | samples number | longitude | |
Mintheta | Float | Minimum value of | ||
Maxtheta | Float | Maximum value of | ||
angularCut | Float | Angular cut [deg] |
HFI Beams[edit]
The HFI scanning beams are a combination of observations of Saturn, for the central parts, and Jupiter, for the wings, as described in the Beams section of this document, and in Section 4.1 of Planck-2015-A07[2] on Hybrid beams. Saturn data are used where they are signal-dominated; when the SNR of Saturn drops to < 9, Jupiter data are used, after binning them azimuthally. Beyond that, i.e., below the noise floor of the Jupiter data, and out to 100 arcmin, a power law (~θ -3) is used, where the exponent is derived from GRASP physical optics models. The figure below, taken from the Beams section of this document, shows graphically the different portions of the beam model.
The beams are provided in FITS files named
- HFI_ScanBeam_{det-name}_R2.nn.fits,
where det-name is of the form 100-1a, and nn is the version number. Each file contains a single IMAGE extension. The image is 6001x6001 pixels of size 2x2 arcsec2 (given in the DELTAX and DELTAY keywords), centred on pixel 3001,3001, and normalised to 1 at the maximum, where X and Y and in the Dxx reference system.
References[edit]
- ↑ Planck 2015 results. IV. LFI beams and window functions, Planck Collaboration, 2016, A&A, 594, A4.
- ↑ 2.02.1 Planck 2015 results. VII. High Frequency Instrument data processing: Time-ordered information and beam processing, Planck Collaboration, 2016, A&A, 594, A7.
(Planck) Low Frequency Instrument
(Planck) High Frequency Instrument
Flexible Image Transfer Specification