The satellite

From Planck Legacy Archive Wiki
Revision as of 11:47, 15 March 2013 by Lmendes (talk | contribs)
Jump to: navigation, search

Overview[edit]

The Planck satellite was designed, built and tested around two major modules:

  • The payload module containing an off-axis telescope with a projected diameter of 1.5m, focussing radiation from the sky onto a focal plane shared by detectors of the LFI and HFI, operating at 20K and 0.1K respectively; a telescope baffle that simultaneously provides stray-light shielding and radiative cooling; and three conical “V-groove” baffles that provide thermal and radiative insulation between the warm service module and the cold telescope and instruments.
  • The service module containing all the warm electronics servicing instruments and satellite; and the solar panel providing electrical power. It also contains the cryocoolers, the main on-board computer, the telecommand receivers and telemetry transmitters, and the attitude control system with its sensors and actuators. The most relevant technical characteristics of the Planck spacecraft are detailed in the Table bellow.

Table. Planck satellite characteristics.

Diameter 4.2 m Defined by the solar array
Height 4.2 m
Total mass at launch 1912 kg Fuel mass = 385 kg at launch; He mass = 7.7 kg
Electrical power demand (avg) 1300 W Instrument part: 685 W (Begining of Life), 780 W (End of Life)
Minimum operational lifetime 18 months Planck operated for 32 months with both instruments; the LFI continues surveying the sky
Spin rate 1 rpm $\pm 0.6$ arcmin/sec (changes due to manoeuvers); stability during inertial pointing [math]\sim 6.5\times 10^{-5}[/math] rpm/h
Max angle of spin axis to Sun 10 deg To maintain the payload in the shade; default angle is 7.5 deg
Max angle of spin axis to Earth 15 deg To allow communication to Earth
Angle between spin axis and telescope boresight 85 deg Max extent of FOV∼ 8 deg
On-board data storage capacity 32 Gbit Two redundant units (only one is operational at any time)
Data transmission rate to ground (max) 1.5 Mbps Within 15 deg of Earth, using a 35 m ground antenna
Daily contact period 3 h The effective real-time science data acquisition bandwidth is 130 kbps
The fully assembled Planck satellite a few days before integration into the Ariane 5 rocket. Herschel is visible by reflection on the primary reflector.

For more information, see #planck2011-1-1.

The service module[edit]

The service module provides the various equipment and instruments housed in it with suitable mechanical and thermal environments during launch and orbit. It is formed by an octagonal box, built around a conical tube, which supports the following subsystems intervening in flight operations:

  • Command and data management.
  • Attitude control and measurement.
  • Power control.
  • Reaction control.
  • Telemetry, tracking and command.
  • Thermal control.

The service module contains all the warm satellite and payload electronic units, with the only exception of the box containing JFETs for impedance-matching to the HFI bolometers, which is mounted on the primary reflector support panel, to allow the operation of the JFETs at an optimal temperature of ∼130 K. The service module holds:

  • Main computer
  • Attitude control computer
  • Data processing units
  • Star trackers
  • LFI electronics
  • Dilution control unit
  • HFI readout electronics
  • 4K compressors
  • Helium tanks: 36000 litres of [math]^{4}[/math]He, and 12000 litres of [math]^{3}[/math]He gas are stored in four high-pressure tanks.
  • Sorption cooler radiator
  • Sorption cooler electronics
  • Sorption compressors (2 redundant units)
  • Hydrazine tanks
  • Medium-gain antenna
  • Telemetry subsystem.
The Planck service module. Figure courtesy of Thales Alenia Space (France).

For more information, see #tauber2010a.

Thermal design[edit]

The performance of the Planck instruments in space is enabled by their low operating temperatures, 20 K for LFI and 0.1 K for HFI, achieved through a combination of passive radiative cooling and three active coolers. The scientific requirement for very broad frequency coverage led to two detector technologies with widely different temperature and cooling needs. Active coolers could satisfy these needs; a helium cryostat, as used by previous cryogenic space missions (IRAS, COBE, ISO, Spitzer, AKARI), could not. Radiative cooling is provided by three V-groove radiators and a large telescope baffle. The active coolers are a hydrogen sorption cooler (<20 K), a [math]^{4}[/math]He Joule-Thomson cooler (4.7 K), and a [math]^{3}[/math]He-[math]^{4}[/math]He dilution cooler (1.4 K and 0.1 K). The flight system was at ambient temperature at launch and cooled in space to operating conditions. The HFI bolometer plate reached 93 mK on 3 July 2009, 50 days after launch. The solar panel always faces the Sun, shadowing the rest of Planck, and operates at a mean temperature of 384 K. At the other end of the spacecraft, the telescope baffle operates at 42.3 K and the telescope primary mirror operates at 35.9 K. The temperatures of key parts of the instruments are stabilized by both active and passive methods. Temperature fluctuations are driven by changes in the distance from the Sun, sorption cooler cycling and fluctuations in gas-liquid flow, and fluctuations in cosmic ray flux on the dilution and bolometer plates. These fluctuations do not compromise the science data.

The contrast between the high power dissipation in the warm service module ([math]\sim[/math] 1000 W at 300 K) and that at the coldest spot in the satellite ([math]\sim[/math]100 nW at 0.1 K) are testimony to the extraordinary efficiency of the complex thermal system which has to achieve such disparate ends simultaneously while preserving a very high level of stability at the cold end. More details on the thermal design of the Planck satellite can be found in the Planck early paper II .

The Standard Radiation Environment Monitor[edit]

(NOTE: Adapted from IEEE TRANSACTIONS ON NUCLEAR SCIENCE, VOL. 50, NO. 6, DECEMBER 2003) The standard radiation environment monitor (SREM) is a particle detector developed for satellite applications. It measures high-energy electrons and protons of the space environment with a [math]\pm[/math]20[math]^\circ[/math] angular resolution, spectral information and provides the host spacecraft with radiation information. SREM was developed and manufactured by Contraves Space in cooperation with Paul Scherrer Institute under a development contract of the European Space Agency. SREM is the second generation of instruments in a programme, which was established by ESA’s European Research and Technology Centre (ESTEC) to:

  1. Provide minimum intrusive radiation detectors for space applications;
  2. Provide radiation hazard alarm function to instruments on board spacecraft;
  3. Assist in investigation activities related to possible radiation related anomalies observed on spacecraft;
  4. Assist in in-flight Technology Demonstration Activities.

The design goals are low weight, small dimensions, low power consumption, combined with the ability to provide particle species and spectral information.

In the case of Planck, the use of the SREM was entirely within the scope of bullets 1 and 3 above as due to the nature of operations no real time alarms where possible

The SREM consists of three detectors (D1, D2, and D3) in two detector heads configurations. One system is a single silicon diode detector (D3). The main entrance window is covered with 0.7 mm aluminum, which defines the lower energy threshold for electrons to [math]\sim[/math] 0.5 MeV and for protons to [math]\sim[/math] 10MeV. The other system uses two silicon diodes (detectors D1/D2) arranged in a telescope configuration. The main entrance of this detector is covered with 2 mm aluminum giving a proton and electron threshold of 20 and 1.5 MeV, respectively.A 1.7-mm-thick aluminum and 0.7–mm-thick tantalum layer separate the two diodes of the telescope configuration.

The telescope detector allows measurement of the high-energy proton fluxes with enhanced energy resolution. In addition, the shielding between the two diodes in the telescope prevents the passage of electrons. However, protons with energies greater than [math]\sim[/math] 30 MeVgo through. Thus, using the two diodes in coincidence gives pure proton count rates allowing subtraction of the proton contribution from the electron channels. A total of 15 discriminator levels are available to bin the energy of the detected events. Any two of the levels can be used to raise an alarm flag when the count rates exceed a programmable threshold. This alarm signal can then be used to control the operation of the spacecraft and its instruments. The detector electronics is capable of processing a detection rate of 100 kHz with dead-time correction below 20%. The SREM is contained in a single box of 20[math]\times[/math]12[math]\times[/math]10 and weighs 2.6 kg (see Fig. 1). The box contains the detector systems with the analog and digital front-end electronics, a power supply, and a TTC-B-01 telemetry and Telecommand interface protocol. By virtue of a modular buildup, the interface can be adapted to any spacecraft system. The power consumption is approximately 2.5 W. An essential input for the interpretation of the detection rates, in terms of particle fluxes, are the energy dependent

The SREM data are provided in the Planck Legacy Archive in the form ofindividual FITS files per calendar day.

The telescope[edit]

The telescope is an off-axis aplanatic design with two elliptical reflectors and a 1.5 m projected diameter and an overall emissivity $\lesssim 1\%$. The optical system was optimized for a set of representative detectors (eight HFI and eight LFI). The performance of the aplanatic configuration is not quite as good on the optical axis as the so-called Dragone-Mizuguchi Gregorian configuration, which eliminates astigmatism on the optical axis, but is significantly better over the large focal surface required by the many HFI and LFI feeds.

The Planck telescope consists of:

1. The primary and secondary reflectors (PR and SR), designed and manufactured by Astrium (Friedrichshafen, Germany);

2. The support structure, designed and manufactured by Oerlikon Space (Zurich, Switzerland).

The footprint of the focal plane as seen by an observer at infinity.

For more information, see Tauber et al. 2010, A&A 520, A2.

For more information, see #tauber2010b.

The instruments[edit]

A complete technical description of the teo Planck instruments can be found here: HFI, LFI.

References[edit]

<biblio force=false>

  1. References

</biblio>

(Planck) Low Frequency Instrument

(Planck) High Frequency Instrument

revolutions per minute

Field-Of-View

Space Radiation Environment Monitor

European Space Agency

European Space TEchnology and Research Centre

Flexible Image Transfer Specification